BT-1-55V60W; BT-1-55V60W-IN

Home

802.3bT PoE Injectors

Welcome to the PoE Texas Manual for the BT-1-55v60w-IN that cost effectively upgrades any non-PoE or PoE port to IEEE 802.3bt and 60 watts!

The purpose of the manual is to help you quickly and effectively navigate the installation and functions of your new Power Over Ethernet Midspan. 

Our goal is to make our products as intuitive and simple to use as possible, so we value your feedback and questions directly to us at service@poetexas.com.  Phone +1-512-479-0317.

Or you’re always welcome to leave questions or comments on our product pages: BT-1-55V60W, & BT-1-55v60w-IN.

What’s Inside

BT-1-55v60w

PARTS LIST:

  • 1 X Midspan Injector with built in 6KV Surge Protection (designed for indoor use only)
  • 1 X AC Power Cable

 

Additional items you’ll need not included:

1 – Screws for mounting

2 – Patch cables to the switch and home run cables to the device

BT-1-55v60w-IN

 

PARTS LIST:

  • 1 X Midspan Injector (without surge protection- designed for indoor usage only)
  • 1 X AC Power Cable

 

Additional items you’ll need not included:

1 – Screws for mounting

2 – Patch cables to the switch and home run cables to the device

General Installation

A midspan like the BT-1-55v60w & BT-1-55v60w-IN are a simple device to add on to a network port, and the purpose is to add or increase the PoE of that port without having to upgrade or pick a less optimal switch.

With this wall mounted device, simply mount it near the networking switch you’d like to pair it with.  Then, using a short Ethernet patch cable from the switch’s data port to the LAN port on the PoE midspan.   Then the POE port adjacent to the LAN port will now have that IEEE 802.3bt (60 watts) power budget and up to gigabit pass through data.

The BT-1-55v60w is also surge protected, so, while it cannot be mounted outdoor, you can connect it to outdoor devices with confidence.  In order to make the surge protection fully functional, you will need to properly ground the connector on the side of the device.

Not sure what grounding is?  Panduit has some great graphics around grounding.

CONFIGURATION

There is no configuration necessary with this device.  Simply plug it in.

  • The green LED indicates power on and drawing less than 30 watts.  If the light turns blue, it indicates the port is drawing more than 30 watts of power.   
  • If the green light begins to blink at any time, it could indicate there is a short in the circuit or a compatibility issue.

 

STEPS TO TROUBLESHOOT:

1 – At the injector, disconnect the PoE port from your device.  Use a PoE Tester to confirm the device is able to power on using a short jumper cable.

2 – At the other end of the network cable to your device, disconnect the device and use the PoE Tester to confirm it is able to negotiate PoE.

3 – Connect the PoE Tester to the end device to monitor power consumption.

 

If you’re able to power on the device with the PoE Tester inline, it’s likely a compatibility issue.  Please contact us at service@poetexas.com to find you the right solution.

Technical Specifications

Product Specifications

AC Plug Connector Type C14
Adapter length 3 ft
Certifications UL/CE/FCC
Data + PoE Ports 1
Data Ports 1
Data Rate Gigabit
Dimensions

6KV Model – 7.6 x 3.3 x 1.6 in.

Indoor Model – 6 x 2.6 x 1.4 in.

Display Type LED – Green (802.3at) ; Blue (802.3bt)
IEC Protection Class IP 40
Input Frequency Range 50/60 Hz
Input voltage 100 – 240 VAC
Load Regulation 6KV Surge Protection on Select model as indicated (BT-1-55V60W)
Max Current 1.1 Amps
Max Power for Kit 60 Watts
Max Voltage 55 volts
Max. Amps Per Port 1.1 Amps
Mount Type Wall
Operating Humidity 20% to 80%
Operating Temperature Range 0 – 40C
Output Voltage 55 volts
PoE Method IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt
PoE Mode/Pinout Mode A (-1,2 +3,6)/Mode B (+4,5 -7,8)

If you find this learning center helpful, like and subscribe on your social channels to learn when we post new guides!

The post BT-1-55V60W; BT-1-55V60W-IN appeared first on PoE Texas.